• The forum software have been upgraded to the latest version.

    If you notice anything that looks off, or does not work, please let us know.

    For more information, click here.

Blog Lord Baconbanes paint blog

LordBaconBane
Ripperdactyl

LordBaconBane

Well-Known Member
Messages
475
Likes Received
1,244
Trophy Points
93
Hey everyone.

For my first post today I'd like to show off my new magnetized Stegadon for all loadouts. I put a lot of work into this guy so I hope you like it.

If you wish to replicate what I did with the Stegadon, you'll need:
- 1mmx1mm magnets (about 5). These magnets will be used for your skinks.
- 2mmx1.5mm (2mmx1mm works too) magnets (about 20). These magnets will be used on the Stegadon bits as they hold much stronger than the 1mmx1mm.


Stegadon Loadouts

20200629_131556.jpg

20200629_131957.jpg

20200629_131931.jpg

Where to magnetize

Stegadon magnetiztion

You're going to want to use the 2mmx1.5 on all the different Stegadon pieces. 20200629_135836.jpg 20200629_131731.jpg

and then apply magnets on the hawdah.

20200629_131633.jpg

I had to trim down some of the horns to make it all fit, but once you apply the pieces on you don't notice they are trimmed.

Skink magnetizing

For the skinks, I applied one magnet in their feet. I found one 1mmx1mm magnet was enough to cling to the 2mmx1.5mm magnets. The only exception is the Skink Chief that has two magnets in his feet. I was considering on putting in a magnet for the skinks foot on the crossbow but decided not too in the end.

What isn't magnetized?
  • The Skinks Priest is glued to the Engine piece
  • Two skinks at left and right of the front part of the howdah are glued on.
  • Nothing in the terrain is magnetized.
Tips
  • Triple check your magnets before gluing them in. I put two magnets in the wrong way and digging them out takes a lot of times and can destroy painted areas.
  • Plan ahead. Check what parts you want to magnetize and do them separate.
  • 2mmx1mm magnets are OK to use, but 2mmx1.5mm magnets do hold a bit stronger.
If you've gotten this far, thanks for you reading :)
 
LordBaconBane said:
Hey everyone.

For my first post today I'd like to show off my new magnetized Stegadon for all loadouts. I put a lot of work into this guy so I hope you like it.

If you wish to replicate what I did with the Stegadon, you'll need:
- 1mmx1mm magnets (about 5). These magnets will be used for your skinks.
- 2mmx1.5mm (2mmx1mm works too) magnets (about 20). These magnets will be used on the Stegadon bits as they hold much stronger than the 1mmx1mm.


Stegadon Loadouts

View attachment 74188

View attachment 74187

View attachment 74189

Where to magnetize

Stegadon magnetiztion

You're going to want to use the 2mmx1.5 on all the different Stegadon pieces. View attachment 74193 View attachment 74191

and then apply magnets on the hawdah.

View attachment 74192

I had to trim down some of the horns to make it all fit, but once you apply the pieces on you don't notice they are trimmed.

Skink magnetizing

For the skinks, I applied one magnet in their feet. I found one 1mmx1mm magnet was enough to cling to the 2mmx1.5mm magnets. The only exception is the Skink Chief that has two magnets in his feet. I was considering on putting in a magnet for the skinks foot on the crossbow but decided not too in the end.

What isn't magnetized?
  • The Skinks Priest is glued to the Engine piece
  • Two skinks at left and right of the front part of the howdah are glued on.
  • Nothing in the terrain is magnetized.
Tips
  • Triple check your magnets before gluing them in. I put two magnets in the wrong way and digging them out takes a lot of times and can destroy painted areas.
  • Plan ahead. Check what parts you want to magnetize and do them separate.
  • 2mmx1mm magnets are OK to use, but 2mmx1.5mm magnets do hold a bit stronger.
If you've gotten this far, thanks for you reading :)
Click to expand...

I am nuts for magnets on models, to field all possible options If you would like.

I have my Stegadon still in the modelling stage so I will make notes of your model ;)

Thanks.

Great painting as well

Grrr, Imrahil
 
Though magnetizing aint my jam, i commend you on your work.
The paintjob is especially nice, i love how you got all the colours so vibrant. Good eye for detail also!
 
LordBaconBane said:
20200629_131556-jpg.74188
Click to expand...

Really beautiful work here, well done! :vulcan:

I really appreciate that you magnetized him!
 
Amazing work! I'm trying this now, but most of mine is already glued together (in sub-assemblies), so I have to ask - when in the process is best to drill the holes for the magnets?
 
alxcore said:
Amazing work! I'm trying this now, but most of mine is already glued together (in sub-assemblies), so I have to ask - when in the process is best to drill the holes for the magnets?
Click to expand...

Thank you!

I started drilling after I had painted everything. But before you drill i highly recommend placing your models on the pices first. Get your big pieces magnetized first so you can see if adjustments need to be made for your little guys. Also, don't YOLO with magnets, check 3-4 times before gluing it in
 
You must log in or register to reply here.
Back
Top